Correct adhesive bonding depends not only on the adhesive system itself, but also on accurate application, controlled working conditions and the right installation tools.
TWEHA therefore offers a range of professional tools specifically selected to support the correct, efficient and safe application of TWEHA Bonding Systems — from adhesive dispensing and climate monitoring to façade panel removal and full-surface adhesive application.
TWEHA Caulking Guns are designed to provide smooth, continuous and controllable dispensing pressure, allowing TWEHA adhesives to be applied accurately and consistently.
A controlled extrusion rate is essential for producing a continuous adhesive bead with the correct geometry and volume. The dispensing mechanism immediately releases pressure when operation stops, helping to prevent unwanted adhesive flow and ensuring cleaner and more accurate
Designed for applying continuous and controlled triangular adhesive beads with consistent output.
The TWEHA Cutting Wire Set is designed for the removal or replacement of façade panels installed with a TWEHA Bonding System.
By positioning the cutting wire behind the façade panel, the adhesive beads can be cut through without unnecessarily damaging the supporting structure. This makes it possible to remove individual façade panels for replacement, inspection, repair or maintenance.
The set consists of a strong braided wire and two solid pull handles. Both handles incorporate a safety provision to maintain distance between the user’s hands and the cutting wire should the wire fail during operation
To remove a panel, the cutting wire is positioned behind the panel through the horizontal joint. Using long, controlled movements, the adhesive beads are progressively cut through.
Important: The façade panel must always be securely supported or restrained before the final adhesive beads are cut. Always wear suitable protective gloves. A new cutting wire should be used for each façade panel. Friction and heat generated during cutting can weaken the wire and increase the risk of breakage.
For removing bonded panels, replacing damaged ones and accessing the space behind the façade.
Suitable for façade repair, renovation and maintenance of ventilated façade constructions.
Allows cured TWEHA adhesive beads to be cut in a controlled manner for bonding-system inspections.
The TWEHA Hygrometer is a professional measuring and data-logging system for continuously monitoring the climatic conditions during the installation of TWEHA Bonding Systems.
Temperature, relative humidity and dew point are important parameters when carrying out façade bonding. Continuous monitoring provides installers with objective information about the environmental conditions during application and supports correct project and warranty documentation. The external sensor communicates continuously with the data logger, allowing climatic data to be registered, stored and subsequently evaluated.
The recorded measurement data can be exported and added to the project or warranty documentation, providing a traceable record of the climatic conditions during installation.
Measures ambient temperature, relative humidity and dew point during façade installation.
Records installation conditions for quality control, project files and site records.
The TWEHA Adhesive Spreader is a professional dispensing solution for the fast, controlled and consistent distribution of adhesives over larger surfaces. Based on the innovative SOPI Flip’n’Spread™ system, the spreader can be connected to adhesive packaging such as foil packs and cartridges and distributes the adhesive through multiple precisely positioned openings. This enables several parallel adhesive beads to be applied simultaneously, providing an efficient and controlled alternative to conventional manual spreading.
The system is particularly useful for applications requiring consistent distribution of adhesives across a larger bonding area. Different outlet sizes are available to accommodate various adhesive viscosities, required application volumes and bonding configurations. SOPI offers opening sizes ranging approximately from Ø2.0 to Ø5.0 mm, depending on the configuration.
The Flip’n’Spread™ concept has been developed specifically to improve application precision and material utilization when dispensing adhesives and other compounds from foil-pack and cartridge systems. Always select the appropriate spreader configuration and adhesive application pattern according to the TWEHA adhesive, substrate, required adhesive thickness and specific application.
Applies multiple parallel adhesive beads with controlled distribution across large bonding surfaces using foil-pack or cartridge systems.
Suitable for large façade and construction panels, as well as stone and ceramic materials.
Designed for panel manufacturing, industrial bonding applications and workshop prefabrication.
Compared to traditional mechanical fixation systems, TWEHA Bonding Systems can reduce installation costs by up to 40%.
Faster installation, fewer components, and no visible fixings result in both economic and aesthetic advantages.
Discover how our product enables cleaner, faster, and more efficient façade installations.
